A gas furnace burns fuel in a sealed chamber, passes the hot gases through a heat exchanger, and a blower pushes warm air across that exchanger and out through your ducts. A control board runs a safety sequence every time the thermostat calls for heat. It starts the draft fan, checks the pressure switch, lights the burners and confirms a flame before the blower comes on. If any step fails, the furnace shuts down on purpose, which is why a furnace often goes quiet instead of making noise.
The most common heating repairs in Memphis involve ignitors that burn out, flame sensors coated with residue, dirty filters that choke airflow and trip the high-limit switch, failed blower motors and capacitors, clogged condensate drains on high-efficiency models, and thermostats that lose their signal. Heat pumps have their own issues, such as a failed reversing valve, a frozen outdoor coil, low refrigerant or a defrost control that stops working. Electric heat can fail from a bad heating element, sequencer or limit switch.
We start by listening to what happened, then work through the system step by step. We check the thermostat, power, filter, ignition sequence, flame, airflow, safety switches and the heat exchanger. If we find something that is not safe to run, we tell you clearly and explain what must be done before the furnace is used again.
Signs your furnace or heat pump needs repair
- If you smell gas, leave the home right away. Do not use switches or phones inside. Call 911 or the gas utility (MLGW) from outside.
- The system does not turn on, or it starts and shuts off after a short time.
- Air from the vents is cold or only lukewarm when heat is called for.
- You hear banging, rattling, squealing or a repeated clicking without ignition.
- Some rooms stay cold, or the furnace runs constantly without reaching the set temperature.
- You see soot, yellow or flickering burner flames, or rust and moisture around the furnace.
- A carbon monoxide alarm sounds. Get everyone outside and call 911.
How a visit goes
- We learn what happenedWe ask what you saw and heard, whether the furnace has done this before, and how old it is. Tell us if a carbon monoxide detector went off or you noticed an odd smell.
- We diagnoseWe check the thermostat and power, then run the heating cycle and watch each stage: draft fan, ignitor, gas valve, burners, flame sensing and blower. We inspect the filter, airflow and safety controls, and look at the heat exchanger for signs of damage.
- We explain the optionsYou hear what failed, what the repair involves and whether it makes sense for your furnace. If the heat exchanger is cracked or the unit is not safe to run, we explain why and discuss replacement.
- We repair and verifyAfter the repair we run a full heating cycle, confirm the flame, airflow and safety controls work correctly, and make sure the home is heating normally.
Questions we hear
My furnace is blowing cold air. What is wrong?
Common causes include a thermostat fan setting left on, a failed ignitor or flame sensor, a dirty filter that tripped the safety limit, or a gas supply issue. If the thermostat is set to auto and heat, and the filter is clean, call us. Do not keep resetting the furnace over and over.
What can I check before I call?
Make sure the thermostat is on heat and set above room temperature, replace a dirty filter, confirm the furnace switch and breaker are on, and check that vents and returns are not blocked. Do not open the gas valve or the burner area yourself.
Is it safe to run a furnace with a bad smell or noise?
A burning smell can be dust at the start of the season, but if it continues, turn the furnace off. Loud banging or a smell like gas is not something to wait on. For gas, leave the home and call 911 or the gas utility from outside. If you are not sure, turn the furnace off and call us.
Do you repair heat pumps?
Yes. We repair heat pumps, including reversing valves, defrost controls, outdoor fans, capacitors and refrigerant issues, and we also service electric heating and gas furnaces.
Should I repair or replace my furnace?
Many failures such as an ignitor, sensor or motor are worth fixing. A cracked heat exchanger, or a furnace that fails repeatedly, usually points to replacement. We explain what we found, and you decide.